Sew a Reversible Bucket Hat for Summer

A lightweight bucket hat is a practical warm-weather accessory and a satisfying beginner sewing project. With two coordinating fabrics, you can make one side playful and the other side simple enough to wear with everyday clothes. The reversible design also gives the hat a neat finish without exposed lining seams.

This project works well for confident beginners because the pattern uses simple geometric pieces: a crown, a side band, and a circular brim. Cotton, linen, denim, or lightweight canvas can all work, depending on the look and structure you want.

The measurements below create an adult-sized hat, with easy adjustments for children and smaller or larger heads. Allow around two to three hours for cutting and sewing, especially if this is your first time working with curved seams.

Pick Fabrics and Sewing Supplies

Choose two tightly woven fabrics with similar weights. Quilting cotton is the easiest option because it presses well and is available in many colors and prints. Linen-cotton blends give the hat a relaxed summer texture, while lightweight denim creates a firmer sun hat.

You will need about half a metre of each fabric for an adult size, matching or contrasting thread, fabric scissors, pins or clips, tailor’s chalk, an iron, and a sewing machine. A compass, large plate, or pattern paper will help you draft the circular pieces.

For extra body, add lightweight fusible interfacing to one brim layer. This is useful when the fabric is very soft, though it is optional. Avoid heavy interfacing if you want the finished hat to fold easily into a beach bag.

Draft a Simple Hat Pattern

Measure around the head where the hat will sit, keeping the tape level and comfortably loose. Add 2 cm for wearing ease. This is the finished circumference of the crown. For a 56 cm head, use 58 cm as the working circumference.

The side band is a rectangle. Its length is the working circumference plus 2 cm for the joining seam, and its height is usually 10–11 cm, including seam allowance. For the crown top, calculate the working circumference divided by 3.14, then add 2 cm for seam allowance around the edge.

A brim is a ring rather than a full circle. Its inner opening should match the crown’s lower edge, and the outer edge should extend 7–9 cm beyond it. Draft half of the ring on folded paper, or draw two circles with a compass. Add 1 cm seam allowance around both the inner and outer curves.

Head Measurement Side Band Cut Size Crown Top Diameter Suggested Brim Width
48 cm 52 × 9 cm 18 cm 6–7 cm
52 cm 56 × 10 cm 19.8 cm 7 cm
56 cm 60 × 10 cm 20.5 cm 7–8 cm
58 cm 62 × 11 cm 21.1 cm 8–9 cm

These figures are starting points rather than strict rules. If you prefer a closer fit, remove 1 cm from the working circumference. For a slouchier bucket hat, add 1–2 cm and increase the side band height slightly.

Cut the Reversible Pieces

For each fabric, cut one crown circle, one side band rectangle, and one brim ring. Label the pieces as Fabric A and Fabric B so they do not get mixed up during assembly. Transfer a small notch to the front and back of each crown circle and side band to make curved sewing easier.

Fold the fabric before cutting the brim if you drafted a half-pattern. Check that the grainline runs consistently through the side band and across the brim. A stable grainline helps the hat keep its shape and prevents the brim from twisting.

Apply fusible interfacing to the wrong side of one brim piece if desired. Press it carefully according to the manufacturer’s instructions, using a pressing cloth when working with delicate fabric. Do not stretch the ring while pressing.

Build Both Hat Halves

Join the short ends of each side band with right sides together. Use a 1 cm seam allowance, then press the seam open or toward one side. You should now have two fabric tubes. Mark four evenly spaced points around the lower edge of each tube and around each crown circle.

Pin one crown circle to the top edge of its matching tube, right sides together. Match the marked points first, then distribute the fabric between them. Curved seams can be eased into place with plenty of pins or clips; avoid pulling the fabric as you sew.

Stitch slowly around the circle. If the fabric puckers, shorten the stitch slightly and check that the seam allowance remains even. Clip small notches into the seam allowance without cutting the stitching, then press the seam toward the side band. Repeat these steps for the second fabric.

Join the Brim and Crown

Place each brim ring over its matching crown section with right sides together, aligning the inner opening with the lower edge of the side band. Pin at the quarter points before filling in the spaces. Sew around the inner curve with a steady 1 cm seam allowance.

Clip the inner seam allowance around the curve, then press it carefully toward the brim. This small step makes the inside of the reversible hat lie flat and prevents the crown from looking gathered. If your fabric frays, finish the raw edge with a zigzag stitch or overlocker.

Now place the two completed hat halves together, right sides facing. Align the outer edges of the brims and the side seams. Stitch around the entire outer brim, leaving a 7–10 cm opening on one side for turning. Sew slowly around the curve for a smooth edge.

Stitch the Final Details

Trim bulky seam allowances around the brim, especially where the side seams meet. Turn the hat right side out through the opening, gently pushing out the outer edge with a blunt tool. Avoid using sharp scissors, which can puncture the fabric.

Press the brim flat, rolling the seam slightly toward the underside so the opposite fabric does not show along the edge. Fold the opening’s raw edges inward and close it with a neat slip stitch by hand or a narrow topstitch.

For a crisp finish, topstitch around the brim in one or more rows. A single line about 5 mm from the edge is simple and understated; several evenly spaced rows add structure and a classic millinery detail. Topstitching also helps the brim hold its shape after washing.

Personalize the Summer Hat

Use the two sides to create different moods: a floral print paired with natural linen, bright stripes matched with a solid color, or a child’s favorite character fabric combined with a plain cotton. Prewash both fabrics so the hat does not shrink unevenly later.

Keep these finishing ideas in mind:

If the hat feels too loose after trying it on, add a few discreet hand stitches inside the side band to reduce the circumference. If it feels tight, remove the topstitching near the back seam and let out the side seam slightly, provided enough seam allowance remains.

Pack the finished accessory by placing the crown inside the brim and folding the ring gently rather than crushing it. Cotton hats can usually be washed on a gentle cycle, but always follow the care instructions for the chosen fabric and interfacing. Handmade fabric provides some shade, yet it should complement sunscreen, sunglasses, and other sun-safe habits rather than replace them.

Gather two fabrics, draft the simple pieces, and sew a reversible bucket hat that can follow you from garden afternoons to summer picnics. Share the finished color combination and make a second version when you find a print you cannot resist.